تماس با ما

فید خبر خوان

نقشه سایت

فروشگاه جامع تحقیقات و مقالات و منابع مهندسی مکانیک


اگر به یک وب سایت یا فروشگاه رایگان با فضای نامحدود و امکانات فراوان نیاز دارید بی درنگ دکمه زیر را کلیک نمایید.

ایجاد وب سایت یا
فروشگاه حرفه ای رایگان

دسته بندی سایت

پر فروش ترین های فورکیا


پر بازدید ترین های فورکیا

برچسب های مهم

آمار بازدید سایت

پیوند ها

آمار بازدید

  • بازدید امروز : 33
  • بازدید دیروز : 87
  • بازدید کل : 246949

مقاله جوشکاری Resistance-Spot-Welded AZ31 Magnesium Alloys: Part I. Dependence of Fusion Zone Microstructures on Second-Phase Particles


مقاله جوشکاری با عنوان :

Resistance-Spot-Welded AZ31 Magnesium Alloys:
Part I. Dependence of Fusion Zone Microstructures
on Second-Phase Particles
L. XIAO, L. LIU, Y. ZHOU, and S. ESMAEILI

چکیده:

A comparison of microstructural features in resistance spot welds of two AZ31 magnesium
(Mg) alloys, AZ31-SA (from supplier A) and AZ31-SB (from supplier B), with the same sheet
thickness and welding conditions, was performed via optical microscopy, scanning electron
microscopy (SEM), X-ray diffraction (XRD), and transmission electron microscopy (TEM).
These alloys have similar chemical composition but different sizes of second-phase particles due
to manufacturing process differences. Both columnar and equiaxed dendritic structures were
observed in the weld fusion zones of these AZ31 SA and SB alloys. However, columnar dendritic
grains were well developed and the width of the columnar dendritic zone (CDZ) was much
larger in the SB alloy. In contrast, columnar grains were restricted within narrow strip regions,
and equiaxed grains were promoted in the SA alloy. Microstructural examination showed that
the as-received Mg alloys contained two sizes of Al8Mn5 second-phase particles. Submicron
Al8Mn5 particles of 0.09 to 0.4 lm in length occured in both SA and SB alloys; however, larger
Al8Mn5 particles of 4 to 10 lm in length were observed only in the SA alloy. The welding
process did not have a great effect on the populations of Al8Mn5 particles in these AZ31 welds.
The earlier columnar-equiaxed transition (CET) is believed to be related to the pre-existence of
the coarse Al8Mn5 intermetallic phases in the SA alloy as an inoculant of a-Mg heterogeneous
nucleation. This was revealed by the presence of Al8Mn5 particles at the origin of some equiaxed
dendrites. Finally, the columnar grains of the SB alloy, which did not contain coarse secondphase
particles, were efficiently restrained and equiaxed grains were found to be promoted by
adding 10 lm-long Mn particles into the fusion zone during resistance spot welding (RSW).


مبلغ قابل پرداخت 2,000 تومان

توجه: پس از خرید فایل، لینک دانلود بصورت خودکار در اختیار شما قرار می گیرد و همچنین لینک دانلود به ایمیل شما ارسال می شود. درصورت وجود مشکل می توانید از بخش تماس با ما ی همین فروشگاه اطلاع رسانی نمایید.

Captcha
پشتیبانی خرید

برای مشاهده ضمانت خرید روی آن کلیک نمایید

  انتشار : ۲۰ تیر ۱۳۹۴               تعداد بازدید : 1302

برچسب های مهم


مطالب تصادفی

  • آموزش تصویری کتاب اینترچنج 3 (Interchange3) توسط مهندس باقری
  • آموزش تصویری کتاب اینترچنج 2 (Interchange2) توسط مهندس باقری
  • Simulation of ODE/PDE Models with MATLAB, OCTAVE and SCILAB
  • Linear Control Systems with solved problems and MATLAB examples
  • MATLAB Codes for Finite Element Analysis

تمام حقوق مادی و معنوی این وب سایت متعلق به "" می باشد